商品説明
3com 3CR17402-31 10/100/1000Mbps 48-Port
48-Port Layer2 SuperStack3 Switch
パスワード/コンフィグレーションは初期化済みです。
ユーザー名admin/パスワードなしでログイン出来ます。
本体に使用感、擦りキズ等があります。
商品詳細
メーカー:3com
製品名:3CR17402-31
P/N:174029-110-000-2.00
ポート数:48 10/100/1000
Hardware EPLD:1.01
Image Loader:2.1.0.22
Runtime:2.1.0.0
Expected module:2.1.0.0
本体サイズ:43.6H x 440W x 325D mm
重量:3.7kg
付属品
電源ケーブル
起動ログ
Hardware EPLD 1.01
Image Loader 2.1.0.22
Loading Diagnostic Image File : Sw3870_diag_V2.1.0.27.bix
Diagnostics 2.1.0.27
User Mode
--- Performing Power-On Self Tests (POST) ---
UART Loopback Test ........... PASS
DRAM Test .................... PASS
Timer Test ................... PASS
PCI Device 1 Test ............ PASS
I2C Bus Initialization ....... PASS
Switch Int Loopback Test ..... PASS
Crossbar Int Loopback Test ... PASS
Fan Speed Test ............... PASS
Done All Pass.
------------------ DONE ---------------------
Loading Runtime Image File : op1.bix
Runtime 2.1.0.0
Expected module version: 2.1.0.0
PCI unit 0: Dev 0x5690, Rev 0x03, Chip BCM5690_A2, Driver BCM5690_A0
PCI unit 1: Dev 0x5690, Rev 0x03, Chip BCM5690_A2, Driver BCM5690_A0
PCI unit 2: Dev 0x5690, Rev 0x03, Chip BCM5690_A2, Driver BCM5690_A0
PCI unit 3: Dev 0x5690, Rev 0x03, Chip BCM5690_A2, Driver BCM5690_A0
PCI unit 4: Dev 0x5670, Rev 0x02, Chip BCM5670_A1, Driver BCM5670_A0
PCI device BCM5690_A2 attached as unit 0.
PCI device BCM5690_A2 attached as unit 1.
PCI device BCM5690_A2 attached as unit 2.
PCI device BCM5690_A2 attached as unit 3.
PCI device BCM5670_A1 attached as unit 4.
Fan controller detected.
Thermal 0 sensor detect.
DNS_ResolverInit..OK
DNS_Proxy_init ....OK
1.Backdoor functions
Enter your choice:
Set Transition mode ...
[get stackingMac done ret_val] = 1
Assigned Unit ID:[1]
0 unitid =1
0 start_module_id =0
0 num_module_id =4
0 expansion_module_id =255
Finish Set Transition mode ...
Enter Transition mode ...
Finish Transition mode ...
Enter Master mode ...
ISC: Stack status: Normal
swdrv Master -
...stack id - 1
...base port ID - 1
...port_number - 48
...units - 1
...unit_tbl[0] - 1
...unit_tbl[1] - 0
...unit_tbl[2] - 0
...unit_tbl[3] - 0
...unit_tbl[4] - 0
...unit_tbl[5] - 0
...unit_tbl[6] - 0
...unit_tbl[7] - 0
...stacking port - 0
Load certificate files : Starting
Load certificate files : Finished
Finish Master mode ...
Performing startup provision ...
......stacking DB: unit = 0, module type = 0
stacking DB: unit = 1, module type = 0
stacking DB: unit = 2, module type = 0
stacking DB: unit = 3, module type = 0
stacking DB: unit = 4, module type = 0
stacking DB: unit = 5, module type = 0
stacking DB: unit = 6, module type = 0
stacking DB: unit = 7, module type = 0
Notify provision complete
Provision Complete ...---- master state preemption
Finish Provision Complete ...
[get stackingMac done ret_val] = 1
auto sync file name startup1.cfg