730 Zeus Appliance Check Point エンタープライズ向け オール・イン・ワン・セキュリティ 初期化済み
- 動作確認済み、中古品です。
- マニュアル等の付属品はありません。
- キズや汚れ、経年による使用感等がございますことを、予めご了承ください。
メーカー |
CheckPoint |
製品名称/型番 |
L-71W |
寸法/重量 |
210 x 42.5 x 155 mm/ 1.3 kg |
LAN |
6 |
WAN |
1 |
DMZ |
1 |
MGMT |
RJ-45 |
付属品 |
ACアダプタ のみです。 |
Annapurna Labs stage 2: stage2_eth3_ram_loader v1.65.1
Executing next!
Annapurna Labs stage 2: stage2.5_loader v1.65.1
SPD I2C Address:00000057
Executing next!
-----------------------------------------------------
Stage 3 version: 1.65.1
Commit ID: xxxxxxx
CVOS commit ID: xxxxxxx
HAL commit ID: xxxxxxx
Build date: May 20 2015 19:57:35
-----------------------------------------------------
EEPROM Revision ID = 37
Device ID = a312
Device Info: AL31200-1700
Loading DT to 00100000 (19149 bytes)...
Board config ID: alpine_db (S1-L71)
Loading application to 00100000 (459564 bytes)...
Executing application...
U-Boot 2015.01-alpine_db_s1-1.65.1-HAL (Nov 17 2016 - 10:24:23) Check Point version: 85
I2C: ready
DRAM: 1 GiB
______ __ __ _______ _ _
.' ___ |[ | [ | _ |_ __ \ (_) / |_
/ .' \_| | |--. .---. .---. | | / ] | |__) | .--. __ _ .--. `| |-'
| | | .-. |/ /__\\/ /'`\] | '' < | ___// .'`\ \[ | [ `.-. | | |
\ `.___.'\ | | | || \__.,| \__. | |`\ \ _| |_ | \__. | | | | | | | | |,
`.____ .'[___]|__]'.__.''.___.'[__| \_] |_____| '.__.' [___][___||__]\__/
power_init_board: EEPROM per device information - using defaults!
Board config ID: alpine_db (S1-L71)
NAND: 1024 MiB
00:00.0 - 1c36:0002 - Network controller
00:01.0 - 1c36:0001 - Network controller
00:02.0 - 1c36:0002 - Network controller
00:03.0 - 1c36:0001 - Network controller
00:04.0 - 1c36:0011 - Cryptographic device
00:05.0 - 1c36:0021 - Base system peripheral
PCIE_0: Link up. Speed 2.5GT/s Width x1
01:00.0 - 168c:003c - Network controller
PCIE_2: Link up. Speed 5GT/s Width x1
02:00.0 - 1912:0015 - Serial bus controller
In: serial
Out: serial
Err: serial
Net: reg=26 data=36928
reg=26 data=36928
, al_eth1 [PRIME], al_eth0
Warning: al_eth0 MAC addresses don't match:
Address in SROM is 00:xx:xx:xx:xx:xx
Address in environment is 00:xx:xx:xx:xx:xx
, al_eth2
Warning: al_eth2 MAC addresses don't match:
Address in SROM is 00:xx:xx:xx:xx:xx
Address in environment is 00:xx:xx:xx:xx:xx
, al_eth3
Warning: al_eth3 MAC addresses don't match:
Address in SROM is de:xx:xx:xx:xx:xx
Address in environment is de:xx:xx:xx:xx:xx
device 0 offset 0x300000, size 0x3fd00000
do_nand: set partition base address to=300000
Trying to read nand: 262144 bytes from offset 3145728
Read nand: 262144 bytes from nand
blob magic: a5a51234
blob crc: 9d7b0f9e
Verifying CRC for settings area... Done
************ Hit 'Ctrl + C' for boot menu ************
Saving Environment to NAND...
Erasing NAND...
Erasing at 0x280000 -- 100% complete.
Writing to NAND... OK
bootargs=boardFlavor=alpine_db_s1 quiet console=ttyS0,115200 noExtPorts= maxcpus=2 cp_net_config=3,(00:F:7E:B7:56)(00:1C:7F:7E:B7:57)(00:1C:7F:7E:B7:58) uboot_ver=85 pci=pcie_bus_perf
device 0 offset 0x380000, size 0x3fc80000
do_nand: set partition base address to=380000
NAND read: device 0 offset 0x380000, size 0x1000000
16777216 bytes read: OK
## Booting kernel from Legacy Image at 08001000 ...
Image Name: Linux-3.10.20-al-5.0-pr2
Created: 2017-12-21 13:00:09 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8658584 Bytes = 8.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 03b2d008
Booting using the fdt blob at 0x3b2d008
Loading Kernel Image ... OK
reserving fdt memory region: addr=0 size=100000
Loading Device Tree to 03b11000, end 03b18acc ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
INIT: version 2.88 booting
Booting Check Point RD-6281-A User Space...
INIT: Entering runlevel: 3
.............
------------- This is a first boot ---------------
...............................................